×
First posts must be approved (25 Oct 2018)

Due to the unwelcome increase in the number of spam posts on the site it is now required for everyone's first post to be approved by a moderator.

Read More...

emo Daihatsu Mira: compomotive th 14" ( now with pictures)

  • GRUSS
  • GRUSS's Avatar Topic Author
  • Offline
  • Kizoku Member
  • The RETRO Jap Pocket Rocket!
More
30 May 2012 11:04 #14058

Got my eye on some compomotive th 14 inch ET 23 and the PCD is 4x108. What is the offset on the Mira wheels? Also I can't remember the center bore diameter either  :ohmy:



oil and filter change *16/01/10 *27/08/10 *06/11/10 *16/04/11 *17/12/11 *17/03/12
Timing belt and tensioner and Alternator belt change 11/06/11
Last Edit: 05 Jun 2012 11:09 by liaderdvilcaci.

Please Log in or Create an account to join the conversation.

More
30 May 2012 11:32 #14061

At a guesstimate I'd say you could fit the et23 wheels on depending on the width of the wheel?

I can't remember but I think the centre bore I had machined in mine was about 72mm

Please Log in or Create an account to join the conversation.

  • GRUSS
  • GRUSS's Avatar Topic Author
  • Offline
  • Kizoku Member
  • The RETRO Jap Pocket Rocket!
More
30 May 2012 11:37 #14063

Hi daz, just found some more but with a offset of 45 and I believe the Mira offset is a 50? So they should be better?
Waiting on the info for the center bore. So with a Pcd of 108 I should get away with wobble nuts?



oil and filter change *16/01/10 *27/08/10 *06/11/10 *16/04/11 *17/12/11 *17/03/12
Timing belt and tensioner and Alternator belt change 11/06/11

Please Log in or Create an account to join the conversation.

  • GRUSS
  • GRUSS's Avatar Topic Author
  • Offline
  • Kizoku Member
  • The RETRO Jap Pocket Rocket!
More
30 May 2012 11:38 #14064

Rim width is 5.5



oil and filter change *16/01/10 *27/08/10 *06/11/10 *16/04/11 *17/12/11 *17/03/12
Timing belt and tensioner and Alternator belt change 11/06/11

Please Log in or Create an account to join the conversation.

More
30 May 2012 11:41 #14065

If its the same as the moves i think it should fit, but I'm not saying for definate as don't want to get it wrong.

I'll look at my move wheels tonyt after work and get back to you :thumb:

Please Log in or Create an account to join the conversation.

  • GRUSS
  • GRUSS's Avatar Topic Author
  • Offline
  • Kizoku Member
  • The RETRO Jap Pocket Rocket!
More
30 May 2012 11:46 #14066

Brilliant cheers  :thumb:



oil and filter change *16/01/10 *27/08/10 *06/11/10 *16/04/11 *17/12/11 *17/03/12
Timing belt and tensioner and Alternator belt change 11/06/11

Please Log in or Create an account to join the conversation.

  • GRUSS
  • GRUSS's Avatar Topic Author
  • Offline
  • Kizoku Member
  • The RETRO Jap Pocket Rocket!
More
31 May 2012 10:38 #14126

Did you manage to find out daz?



oil and filter change *16/01/10 *27/08/10 *06/11/10 *16/04/11 *17/12/11 *17/03/12
Timing belt and tensioner and Alternator belt change 11/06/11

Please Log in or Create an account to join the conversation.

More
31 May 2012 11:54 #14128

Soz i didnt manage it last nyt, ill try n find a spare wheel tonyt n get the measurements off it wen I'm back from hospital.

Think I fractured my wrist again yesterday so couldnt jack up the car ::)

Will post up late tonyt or tomorow morning :thumb:

Please Log in or Create an account to join the conversation.

  • GRUSS
  • GRUSS's Avatar Topic Author
  • Offline
  • Kizoku Member
  • The RETRO Jap Pocket Rocket!
More
31 May 2012 12:34 #14131

How've you done that?  :(

I've been doing abit of research and I've not messed with different wheels since my teens so I'm quite out of touch. However am I right in thinking that I should get away with these off of eBay...

http://www.ebay.co.uk/itm/221035304659?ssPageName=STRK:MEBIDX:IT&_trksid=p3984.m1952.l2649#ht_500wt_922

From what I can tell the offset will mean I'll have plenty of room between the rim and the suspension/inner rear arch to allow for the tyre.

I should get away with normal nuts or wobble nuts to allow for the 108pcd?

The center bore will need machining larger for my hubs but I could get the rear face (where it mounts to the hub) machined as well if there sticking out too much to increase the offset ( moving closer in I think?)

I'm currently trying to track some little spats down for the aches, I don't want anything too big.

I'm after something like this setup...



Hope the wrist ain't too bad!



oil and filter change *16/01/10 *27/08/10 *06/11/10 *16/04/11 *17/12/11 *17/03/12
Timing belt and tensioner and Alternator belt change 11/06/11
Last Edit: 31 May 2012 12:36 by iztelcontdanphe.

Please Log in or Create an account to join the conversation.

31 May 2012 13:03 #14136

Think I fractured my wrist again yesterday so couldnt jack up the car ::)

OH no! Hope you feel better soon.


Author of The Ruins of Rytus Series
Sample, purchase or find out more at:
www.RuinsofRytus.com

Connect with me:
Facebook
Twitter
LinkedIn

Please Log in or Create an account to join the conversation.

Moderators: TADOAdam Kenneydazran
Time to create page: 0.589 seconds
Powered by Kunena Forum